氨水溶液制备ZnO纳米晶阵列的研究

以氨水和硝酸锌为前躯体，采用低温水溶液法在涂敷ZnO晶种层的玻璃衬底上外延生长了ZnO纳米棒晶阵列。应用SEM、TEM、SAED和XRD表征了ZnO纳米晶的形貌和结构。讨论了该组成体系水溶液法纳米棒外延生长的机理及其对棒晶形貌的影响。通过对水溶液pH值的原位二次调整，制备出了ZnO纳米管和表面绒毛状的棒晶阵列，基于生长机理探讨了它们的形成原因，为实现不同形貌ZnO纳米晶阵列的优化控制提供了可能的技术途径。结果表明，不同形貌的ZnO均属沿c轴择优取向的六方纤锌矿结构。     

Adaptation of Cu/ZnO/Al_2O_3 to Temperature Change in Methanol Synthesis from CO_2 Hydrogenation

The induction behavior in CO2 hydrogenation was studied by varying the reaction temperature to investigate the adaptation of the Cu/ZnO/Al2O3 catalyst to the temperature change. The results indicated that a used catalyst had a tendency to keep the last running state in new reaction conditions for MeOH formation, and that this tendency was related to the difference in Cu/Cun+ ratio caused by CO2 and CO produced at different reaction temperatures. However, the reverse water-gas shift reaction (RWGS) induced at four temperatures was completely different from that of methanol synthesis. It implied that the two so-called competitive reactions in CO2+H2, RWGS and methanol synthesis, have different active centers.     

加料方式对CuO/ZnO/Al2O3系催化剂前驱体性质的影响

用XRD、TG-DTG、TPR技术研究了不同加料方式对CuO/ZnO/Al2O3系催化剂前驱体物相组成及其结晶情况的影响，用加压微反装置考察了催化剂合成甲醇反应活性。结果表明, 加料方式对Cu2+形成的中间化合物的物相组成及结晶度影响显著,对Zn2+及Al3+的沉淀物相的影响很小。不同加料方式对催化剂前驱体物相组成及催化剂性能的影响主要是形成的初始前驱体中Cu的物相及结晶度不同。正加法主要形成Cu2(OH)3NO3,并流法主要形成无定形Cu2CO3(OH)2,后者与Zn5(CO3)2(OH)6相互作用转化为(Cu,Zn)2CO3(OH)2和（Cu,Zn）5(CO3)2(OH)6，由它们分解形成的CuO-ZnO固溶体是合成甲醇反应的活性相。并流法能最大程度的形成CuO-ZnO固溶体，有利于CuO粒子的细化，其催化活性较好。     

TiO2-CdS-MCM-41复合纳米材料的合成和表征

利用γ-巯丙基三甲氧基硅烷及表面预吸附水解技术在MCM-41介孔分子筛孔道内部以化学键合的形式依次引入了CdS和TiO2纳米粒子.紫外-可见吸收光谱结果表明,借助于巯基的络合能力,MCM-41能有效地从反胶束中萃取CdS纳米粒子.利用小角XRD谱图成功地跟踪观察到了MCM-41介孔分子筛随纳米粒子的引入而产生的孔径变化.     

Hydrothermal Synthesis and Optical Properties of ZnO Nanostructured Films Directly Grown from/on Zinc Substrates

Uniform ZnO nanorods arrays are grown directly from and on Zn foils in pure water under hydrothermal conditions at a relatively low temperature. The nanorods are 80–200 nm in diameter and ∼ 1 μm in length, which grow on the Zn foil along the [001] direction. By changing the pure water to a urea solution, a Zn compound ([Zn₅(OH)₆(CO₃)₂], a precursor of ZnO nanoflowers film, is created by self-assembly. The ZnO nanoflowers film can be easily obtained by heating the [Zn₅(OH)₆(CO₃)₂] compound in N₂ at 350∘C for 5–6 hours. Possible growth processes of the ZnO nanorods arrays and the [Zn₅(OH)₆(CO₃)₂] nanoflowers are discussed. Photoluminescence properties of the as-prepared ZnO nanostructures have been measured. The ZnO nanorods array synthesized using our method has minimal defects so that only band-gap emission is observed. However, the ZnO nanoflowers film, obtained by heating the [Zn₅(OH)₆(CO₃)₂] nanoflower precursor in N₂, is polycrystalline and displays strong defect-related emission.     

一维棒状ZnO的制备及电化学嵌锂性能研究

目前,商业化锂离子电池一般采用石墨作为负极材料,因其电位与金属锂电极的电位很接近,所以当电池反复循环和过充时,石墨表面易析出金属锂,会因形成枝晶而短路。在温度过高时还容易引起热失控。同时,锂离子电池的容量在很大程度上取决于负极的锂嵌入量,而且石墨材料容量相对较低     

碳纳米管/ZnO纳米复合体的制备和表征

通过将不同直径的ZnO纳米颗粒与碳纳米管连接制备了碳纳米管/ZnO纳米复合体. 将团聚的ZnO纳米颗粒分散并用表面活性剂CTAB使纳米颗粒带正电. 化学氧化碳纳米管使其带负电. ZnO/CTAB微团通过碳管表面羧基与CTAB的静电作用与碳纳米管连接形成纳米复合体. 研究了复合体形成的不同实验条件, 表征了碳纳米管/ZnO纳米复合体的结构并研究了纳米复合体的光学特性. 研究表明, 与碳纳米管连接的ZnO纳米颗粒是互不连接的并保持量子点的特性. 光致发光研究表明ZnO纳米颗粒的激发在纳米复合体中有淬灭.     

Electrochemical Studies of Oxidation of Lomefloxacin and Interaction with Calf Thymus DNA at Nano‐SnO2/DHP Modified Electrode

A nanoparticle thin film modified electrode has been constructed using a glassy carbon electrode (GCE) coated with a nano‐tin oxide/dihexadecylphosphate (nano‐SnO₂/DHP). In pH 6.0 phosphate buffer solutions (PBS), lomefloxacin (LMF) appeared as an anodic peak with peak potential of 1.35 V at nano‐SnO₂/DHP modified electrode. In comparison with a bare GCE or a nano‐SnO₂ modified electrode, the nano‐SnO₂/DHP modified electrode exhibited an enhanced effectiveness for the oxidation of LMF. Cyclic voltammetry (CVs) coupled with fluorescence and UV/vis absorbance spectra techniques were used to study the interaction of LMF with Calf thymus DNA (ctDNA) in phosphate buffer solutions (PBS). The interaction of LMF and ctDNA could result in a considerable decrease in the peak currents and positive shift in the peak potential, as well as changes of fluorescence, UV/vis adsorption spectra and gel electrophoresis. All the acquired data showed that the new adduct between LMF and ctDNA was formed. Electrochemistry coupled with spectroscopy techniques could provide a relatively easy way to obtain useful information about the molecular mechanism of LMF‐ctDNA interactions.     

Pt微粒修饰纳米纤维聚苯胺电极对甲醇氧化电催化

以脉冲电流法制备的纳米纤维状聚苯胺(PANI)为Pt催化剂载体，用它制备了甲醇阳极氧化的催化电极Pt/（nano-fibular PANI）.研究结果表明, Pt/（nano-fibular PANI）电极对甲醇氧化具有很好的电催化活性,并有协同催化作用.在相同的Pt载量条件下， Pt/（nano-fibular PANI）电极比Pt微粒修饰的颗粒状聚苯胺电极Pt/(granular PANI)具有更好的电催化活性.此外， Pt的电沉积修饰方法同样影响Pt/（nano-fibular PANI）电极对甲醇氧化的催化活性.脉冲电流法沉积Pt形成的复合电极较循环伏安法电沉积得到的Pt复合电极具有更优异的催化活性.     

累托石/聚丙烯插层纳米复合材料的制备与性能

采用熔融共混法制备了有机改性累托石 (OREC)粘土 均聚聚丙烯 (PP)纳米复合材料 ,以X 射线衍射分析 (XRD)及透射电子显微镜分析 (TEM)观察了复合材料的相貌结构 ,研究了复合材料的力学性能及热性能 .结果表明 ,OREC在添加份数较少时可与均聚聚丙烯熔融插层形成插层型聚丙烯纳米复合材料 ,该复合材料与纯PP相比 ,具有较高的拉伸强度、断裂伸长率及冲击强度 .在有机粘土添加 2 %时 ,复合材料的拉伸强度、断裂伸长率、冲击强度最高 ,与纯PP相比 ,2 %添加量的聚丙烯纳米复合材料拉伸强度提高 6 5 7% ,断裂伸长率提高 2 89 3% ,冲击强度提高 14 1% ,10 %失重率时对应的热分解温度提高 50K .